







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Silestone Home Additions & ADU: The East Los Angeles Owner’s Guide
A Silestone-surfaced addition or ADU in East Los Angeles typically runs $53,100 to $153,400 for a home addition and $106,200 to $259,600 for a full ADU, and that range covers the framing, the rough-in, the slab or quartz tops, and the finish work under one written price. When a homeowner comes to us about a failure, it’s rarely the stone itself. It’s the joint where the Silestone top meets a wall that has moved, an undermount sink that’s pulled loose in a slab that was set on a substrate that never should have passed, or a topping slab that’s cracked across a cold joint in a converted garage. We write the scope, the price, and the guarantee before any tool comes out.
Key takeaways:
- Additions in East Los Angeles land at $53,100 – $153,400; ADUs at $106,200 – $259,600.
- Silestone is an engineered quartz. It’s stable and non-porous, but it doesn’t flex and it won’t take a hot pan or a direct impact.
- Every completed project carries the 365-Day Done Right Promise. If the work fails inside that year, we come back and correct it at no charge.
- The written price is fixed before work starts. No numbers that move at the door.
Which Silestone Models This Applies To

Silestone isn’t a machine with a model number stamped on a plate. It’s a quartz surface sold in named colorways and thicknesses, and the “part” that matters for an addition or ADU is the slab, the edge profile, and the substrate under it. We work with the standard 2 cm and 3 cm slab thicknesses. The 3 cm slab is the one most East Los Angeles islands and ADU kitchen counters get, because it can carry a wider overhang without a plywood build-up under the edge. The 2 cm slab needs a substrate and is common on bath vanities where the span is short.
To identify what you’re working with, look at the underside of the counter near the sink or the dishwasher cutout. Most installers leave a manufacturer sticker or a chalked batch mark there, and the colorway name is usually written on it. If the sticker is gone, pull the drawer above the cutout and look at the exposed slab edge: 2 cm reads as about three-quarters of an inch, 3 cm reads as just over an inch. That measurement tells us what we’re dealing with before we ever price the job.
On the OEM-versus-aftermarket question: quartz slabs are cut to size on site, so there’s no “OEM part” in the car-parts sense. What there is, and what we insist on, is a documented material. Silestone has manufacturer specs and a warranty behind the slab, and those specs are what our own guarantee leans on. We install Silestone, and we also work with KraftMaid, Cambria, and Kohler when a homeowner wants to line up the cabinets and fixtures alongside it. Bradford Remodeling Co East Los Angeles is an independent service provider and is not affiliated with Silestone.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Silestone Home Additions & ADU Is Failing
Five things we see on East Los Angeles jobs, and the cause behind each:
- A hairline crack running from a corner cutout. Quartz doesn’t flex, so a slab set over a high spot in the substrate or a framing member that has moved will crack at the nearest stress point, usually the sink corner. It’s a substrate problem showing up in the stone.
- An undermount sink that’s dropped or separated. The epoxy or mechanical clips let go when the cutout edge was never polished or when the cabinet run has shifted. In older ADU conversions, we regularly see it after a slab-on-grade floor seasonally heaves.
- A counter that rocks when you press on it. Leveling shims under the cabinets have compressed against a floor that wasn’t flat to begin with. The stone stays straight; the cabinets below it don’t.
- Discoloration or a dark ring near a seam. A seam that wasn’t bonded tight lets moisture into the substrate, and the wood swells and stains. Silestone itself doesn’t absorb water, but what’s under it can.
- A joint that’s opened against a wall. A structural addition settles in its first years. The stone stays put and the wall moves away from it. That’s a joint repair, not a counter replacement.
One safety note up front: a 3 cm quartz slab weighs roughly 20 pounds per square foot, and a standard kitchen island top runs several hundred pounds. This is not a two-person carry-and-lift job with a pry bar. Quartz breaks unpredictably and the broken pieces are sharp. If a slab is loose, cracked through, or still bonded to a failing substrate, that’s work for a trained crew. We’ll say the same thing on the phone.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For East Los Angeles, a Silestone counter installation runs $2,360 – $7,670, a kitchen island installation runs $3,540 – $11,800, and a bathroom vanity installation runs $945 – $3,540. Those are installed ranges, and they include the slab, the edge fabrication, removal and disposal of the old top, the cutouts, and the set.
What pushes a job toward the top of a range: a long sink cutout that needs a build-up under the edge, an island wider than 40 inches that needs a seam, a farmhouse sink that needs an apron cut, or a substrate rebuild because the cabinets below are out of level. What keeps it at the bottom: a straight run with one sink, no seams, cabinets that are already flat and sound.
Every job gets a written, line-item price before any work starts. The 365-Day Done Right Promise covers the work for a full year: if something we installed fails to hold inside that window, we return and correct it at no charge, and you’re holding the signed written guarantee at job close.
DIY or Call Us?
What you can safely check yourself: look for the manufacturer sticker under the counter, measure your slab thickness near an exposed edge, check whether the counter rocks when you press on the front edge, and take a photo of any crack from a foot away so a crew can gauge it on the phone. Those four things cost nothing and tell us a lot.
Where DIY goes wrong: lifting, moving, or prying a bonded slab. Quartz can’t be uninstalled like a laminated top, and a slab that lets go under load will break, and the break is dangerous. A dropped slab can cut through a hand or a foot. The real fix, when the substrate or the framing has moved, is to correct what’s underneath before the new top goes on, and that’s the part that doesn’t show and the part a homeowner can’t easily verify.
Call (833) 520-6636 to schedule a free estimate. A live person answers, any hour.
FAQs

The slab itself should last decades. The failure points are the substrate, the seams, and the cutout edges, and those are what determines whether you get ten years or thirty. East Los Angeles homes on a slab, especially converted garages and newer ADUs, tend to move seasonally with the ground, so the shallow cabinet run and the stone above it are where we look first.
Sometimes. A crack that stops short of the full slab width, or a joint that’s opened against a wall, can often be bonded and refinished so it reads as a hairline. A crack that runs clean through a cutout, or one over a substrate that has failed, gets replaced, because a repaired slab over a moving base will crack again. Call (833) 520-6636 for an exact quote, and estimates are free.
A straight run with one sink is typically a two-day job: template on day one, fabrication in the shop, install on day two. An island or a bath vanity with a difficult cutout adds a day. Resurfacing work, like a wall or ceiling repair in an East Los Angeles addition where the joint has opened, adds its own time, and we put that in the written scope so the timeline is on paper.
We work through a documented roster of name-brand suppliers, so a Silestone colorway can be ordered to spec. That matters because a quartz install is a sequencing job: the slab, the cabinets, and the plumbing rough-in have to line up, and a documented material means the specs and the manufacturer warranty are traceable. You’ll have the colorway name, the thickness, and the edge profile in writing before the order goes out.
If you’re weighing an addition or an ADU in East Los Angeles with a Silestone kitchen at its center, call (833) 520-6636 for a free estimate. Our technicians have up to 22 years of experience, and you’ll get a written price before a single tool comes out.
Written by the team at Bradford Remodeling Co East Los Angeles, serving East Los Angeles and nearby areas.












